Rhijnauwen

1 November startte als een mistige dag. Maar na het ontbijt was het zonnig. We maakte een prachtige wandeling langs de Kromme Rijn bij Rhijnauwen. We hebben genoten.

Langs de Kromme Rijn tegenover het Pannenkoekenhuis

Brug bij Bunnik

Boerderij

Tegenlicht

Bij Rhijnauwen. 

Autumn colors

For the last week(s) I very much enjoy the colors of the autumn.
During a bike trip in my village I made a few photo's.
No sun, but I enjoyed the beautiful colors.

eQSL of Mitsuoka JO3JIS

While running through my log, to answer many eQSL's, that I had received, I noticed that I had made a QSO with JO3JIS, but not yet sent a QSL.  I checked and found out that JO3JIS used eQSL, so I send him my card, with the calculated "Miles per Watt" information. I  am very pleased by the quick response, because the next day I received a very nice return eQSL.

JO3JIS   -   2.7 W   -   5400 Miles   -   2110   Miles per Watt

In this QSO I used 2.7 watt. With a distance of 5400 miles, the QSO is good for 2110 Miles per Watt. hi. The distance from my QTH, in the center of The Netherlands, to Japan is more than 5000 miles. So each QSO with Japan made with 5 watts or less, is good for more than 1000 Miles per Watt. My antenna is an Inverted Vee. The antenna of Mitsuoka is a Cushcraft.
Thanks for the very nice DX QSO, Mitsuoka. Hpe cuagn.

Received eQSL's with very low power

The last weeks I answered a lot of eQSL's.
In the INBOX I found many eQSL of QSO's, that were made with 5 W down to 5 milliwatt.

In many contest QSO's, I often reduce to the lowest possible power.
I start with a power that is probably to low.
When my signal is not heard, I increase my power with a small step.

I show here, a few eQSL's that were made with 36 mW and 80 mW and an Inverted V

36 milliwatt 

F5IN  -  36 mW - 295 miles - 8200 Miles per Watt

F6HKA  -  36 mW - 464 miles - 12886 Miles per Watt

80 milliwatt 

OH2BV  -  80 mW - 953 miles - 19111 Miles per Watt

ES5Q  -  80 mW - 955 miles - 15117 Miles per Watt

R7AB  -  80 mW - 1602 miles - 20020 Miles per Watt

My FT-817 makes 360 mW on the lowest setting.
I reduce 360 mW with an attenuator of 10 dB to 36 mW.
On the setting for 1 W, my FT-817 gives 800 mW.
After the 10 dB attenuator, only 80 mW goes to the inverted V.

Truckrun

Gisteren ben ik, als begeleider van een bewoner van de Cruquiushoeve, mee geweest met de Truckrun, Dit fantastische evenment wordt georganiseerd door Stichting Het Reservewiel.

Er vertrokken zo'n 80 trucks vanaf het terrein van de Cruquiushoeve in de Haarlemmermeer.

De lange stoet van vrachtwagens maakte al toeterend een rondritdoor de Haarlemmermeer.

Langs het gemaal De Cruquius

Het konvooi van bijna 85 trucks werd begeleid door 30 verkeersregelaars op motoren en een aantal agenten op motoren en in de auto.

De route ging dit jaar van de Cruquius, naar Zwanenburg en Badhoevedorp. Onderweg werd het konvooi opgewacht met een ereboog van water door de de brandweer. We kregen de volle laag van links en van rechts.

Brandweer - links en rechts

Via  Hoofddorp reden we weer terug naar de Cruquiushoeve.

Bij elke zijstraat en zijweg waar maar verkeer uit kon komen, bleef een gemotoriseerde verkeers regelaar achter, om de stoet ongehinderd door te laten gaan. Als alle trucks gepasseerd waren werd de weg weer vrij gegeven.

Verkeers regelaars

Daarna reed de motor weer langs de stoet helemaal naar voren.

We zaten in dit "rolstoel" busje

We hebben met volle teugen genoten.

Jubileumboek BQC

Jubileumboek BQC

1975 - 2015

40 jaar 

Benelux QRP Club

Het was mij begin deze week al opgevallen, dat de Nieuwsbrief van de Benelux QRP club nog binnen was. Vandaag vroeg mijn vrouw: "heb jij wat besteld?", toen ze zag, dat er een pakket in ons kleine buitenbusje zat.

Het pakket bevatte het Jubileumboek BQC en de nieuwe nieuwsbrief van september 2015. Het Jubileumboek bevat vele interessante artikelen uit 40 jaar BQC nieuwsbrief en telt maar liefst meer dan 290 pagina's. De artikelen bestrijken een periode vanaf de oprichting van de BQC tot nu.
Petje af, voor zo'n dik en goed verzorgd boek dat is samengesteld door Ben Santen en is bewerkt door Marc Schijven.

CQ WW WPX CW contest 2015 with an indoor 15" Cylinder dipole

Monster Cylinder Dipole PA1B

I had great fun in 56 QSO's with my
 Mønster  Cylinder Dipole in the CQ WW WPX 2015.  (Click on the picture to enlarge)

The monster antenna consist of  two
 Mønster Energy Drink Cans  
and a coil of 80 mm with 8 turns.
I determined the number of turns of the coil by experimenting.

This very short antenna has a wingspan of 15" or 38cm. "Indoor" results are best if you place the antenna as high as possible.

By making QSO's in a major contest, I could discover the properties of this very short antenna. All QSO's are made with CW and with S&P (Search and Pounce). As a low power enthusiast, I will reduce my power when the received signals get stronger.

On Saturday I worked with the Monster Dipole in  the shack, on a height of 4 meters above the ground. On Sunday morning I placed the antenna in the dormer window in the attic, on a height of 7 meters above the ground. 

Saturday
On Saturday I started on 14 MHz. Between QSO #3 and #4 we went to a fair. After working 6 stations all on 14 MHz, I went to 21 MHz.
The 15 meter band was open, so I made all QSO's on this band from 12 UTC until 19 UTC. From time to time I went back to 14 MHz, but with NO success.  After 19 UTC I could make just one QSO on 20 mtrs. After this QSO an other 16 QSO's were made on 15 m.
After 19 UTC the signal were stronger, so I could reduce my power. I  could make QRPp QSO's with 720 mW, 360 mW and even one QSO with 72 mW.

Miles per Watt
As a low power enthusiast, I reduce my power before answering a CQ, when the S-meter goes up.
It was great fun to make a QSO with 72 mW with YT6A, over a distance of 851 miles.
This QSO is good for 11820 Miles per Watt.

Thanks to Ranko with his sensitive station with Excellent Ears. FB.

Sunday
On Sunday morning I had time until 10 UTC. The first QSO was made with the Island of Man on 7 MHz. To work on 7 MHz I tune the SWR for 1:1. After breakfast I decided to move the Monster Cylinder Dipole to the attic, just to test whether I could make more QSO's on 14 MHz.The test is not conclusive, because I made the same number of QSO's at the same time as on Saturday.
Between 10 and 18 UTC we visited two birthdays. after 18 UTC I made a few QSO's.

Does it work?
The Cylinder Dipole definitely works.
Because I had limited time on Sunday afternoon, I can not tell whether the antenna works better on the attic on 14 MHz. But I can tell you that it works.

In the interesting table below I show the QSO's from hour to hour.
Please notice the peak in the propagation on Saterday from 19-21 UTC.
I worked 7 stations with  360 mW. But that was not all.

The QSO with 72 mW is years later, still the QSO with the lowest power on the Monster Dipole. Hi.

I am very pleased with results of the Monster Dipole.

CQ WPX CW 2015 with an indoor 15" Cylinder dipole PA1B

When did you make QRP QSO's with 20 DXCC counties on a indoor antenna with a wingspan of 38 cm or 15 inch? Hi.

Worked DXCC's in the CQ WPX CW 2015 with an indoor 15" Cylinder dipole PA1B

Solar Eclipse WPA of WSPR spots by PE4BAS

Solar Eclipse WSPR Propagation Analysis (WPA) of spots by PE4BAS.
The spots were made on 160 mtr, during daylight hours.
The lower the Lowest Possible Power, the better the propagation.

10 dB attenuators of Stefano IZ1OQU

On my Blog and website I show information, on how I work with QRP and QRPp and the use of attenuators for more than 1000 Miles per Watt QSO's.

Stefano IZ1OQU built a 10 dB attenuator, that I described in an earlier post. (Click to read) With this attenuator Stefano made QSO's with 50 milliwatt in SSB from his home over more than 2000 kilometers, using vertical antenna's.

With a difference of 13 dB between SSB and CW, the 50 mW in SSB can be compared with 2.5 mW in CW.
Congrats to Stefano, for this great achievement.

Stefano has recenly built a light weight attenuator with two sections of 10 dB. He wants to use the attenuator in SOTA and portable operation.
Here is the interesting e-mail from Stefano with photo's of the light weight attenuator.


Dear Bert,
I'm IZ1OQU Stefano. I wrote to you some months ago for the attenuators on your website.
With the 50 mW of the first attenuator that I built, I had my best Miles per Watt SSB QSO's with Finland, Russia and Georgia, over 2200 kms with the top-score of 2700 kms with Georgia: 
54.000 kilometers per watt.

I'm writing again to show to you the new step attenuator that I've made: with switches and 2x 10 dB steps to reach the 5 mW output with my FT-817.
I attached some images of the new toy, made with pcb enclosure. I left one removable side just to shot some photos. You'll see, It's tiny (about 6x3x3 cms size) and low-weight. With that small space it was hard to solder everything but I did it!

I'll look forward to find ways to reduce again the size wile adding more steps but not before some testing: you know, SSB is not the best way to play MxW with such little power but I am still newbie with CW.

I keep following your blog, I shared it to some friends because they also like MxW, QRP and homebrewing things. The MxW comunity in Italy is slowly growing thanks to the WxM (watt per mile, or mile per watt... anyway we call it, it's the same thing) contest.
Go on with your good job

73 from Italy
Stefano IZ1OQU 

Light weight 2 x 10 dB attenuator IZ1OQU 

Stefano will use the attenuator on SOTA and portable operation. FB.
To read more, visit Stefano's interesting QRZ page by clicking on the link.

Cylinder dipole at 21 MHz

Monster Cylinder Dipole
Click on the pictures to enlarge

Monster Cylinder Dipole
 After the experiment with the Red Bull antenna, I built a second Cylinder Dipole with two Monster energy drink cans of 500 ml. The cans together with the coil resonate at 16 MHz.
The Monster Cylinder Dipole has a wingspan of 15" or 35 cm. Hi.

The 300 ohm ribbon is connected to the point at the top of the coil (in the picture) with the red and yellow alligator clips (See the white arrow in the top of the picture). The antenna is hanging from the ribbon. I can adjust the SWR 1:1 with my symmetrical tuner.


Cylinder dipole

PA1B Cylinder Dipole.  The current at the surface of the cylinder generates the field.

Closed Monster Cans  
In this antenna I use the complete can, without removing the top and the bottom of the can, to keep the construction simple and the cylinders strong. Closed cylinders are much stronger than open cylinders.

Monster cans
Although it is not easy to compare two antenna's, that were used in two different contests a week apart, the cylinder dipole with the 500 ml Monster cans is probably better than the Red Bull antenna.
In general the cylinder dipoles are very quite on receive, because of the small length of the antenna.

On the air
In the H.M. King of Spain contest I made QSO's on 7 MHz, 14 MHz and 21 MHz.
Most QSO's were made on 21 MHz with a power of 3.6 W to 360 mW all over Europe.
This Monster cylinder dipole with two 500 ml cans works better on 21 MHz than on 14 MHz.
The SWR of the antenna is adjusted with the symmetrical tuner.
On 7 MHz it was very difficult to make a QSO. The QSO's on 7 MHz were made over a short distance. NVIS. The low relative heigh at 7 MHz reduces the signal.

The table below shows the DXCC countries per band and per power category.

Across the Atlantic
I very much enjoyed the QSO with N1KWF in New Hampshire over a distance of 3490 Miles, with a power of 3.6 Watts.

Please notice that that the Monster cylinder dipole with 500 ml cans:
 * has a length of 15" (38 cm)
 * is placed in the shack,
 * at a height of 4 meter above the ground.

Click on the table below, to read the hand written notes.
In this way, I record the power that I use in each QSO, on paper .
The QSO data is logged in SD of EI5DI.

 

List of QSO's with the Monster cylinder dipolePA1B

The QSO's in red are more than 1000 Miles per Watt QSO's.

 

DXCC's per band and per power category PA1B

Red Bull Test Antenna

When I putted the  Red Bull  antenna into use, during the ARI DX 2015, I was aware of the controversial nature of short antennas. But I had absolutely NO doubt about this short antenna, with it's "wingspan" of just 12 inch.
I was convinced that I could make QSO's with QRP or even QRPp from the shack.

Why?
I was curious, whether the  Red Bull  antenna  could be used on 14 MHz, although it was tuned at 26 MHz, in stead of 14 MHz.

Further I was curious, whether the symmetrical tuner could be used to get a SWR of 1:1

I clamped the PVC tube of the antenna between  the bookshelf and connected a 300 ohm twin-lead between the symmetrical tuner and the coil of the antenna. 

The coil had 14 turns on a 40 mm coil former. I did not bother to change the coil to lower the operating frequency, which was 26 MHz and thus much higher than 14 MHz, on which I would operate. The 300 ohm ribbon is is equipped with two alligator clips, which are connected to two connection points on the coil one turn apart.

Red Bull test antenna May 2015 PA1B

SWR.

The tuning runs smoothly. It's very easy to get a accurate SWR of 1:1 So I could transmit with the antenna. I only tried 14 MHz, because that was, where the action was and I wanted to make QSO's immediately. I did not try 21 MHz or 28 MHz.. 

Does it work? Yes.
I convinced myself with 360 milliwatt, with the antenna indoor, at a height of 4 meter above the ground.  Is it not amazing.

The first QSO that I made with this 12 inch antenna, was a more than 1000 Miles per Watt QSO.

On the air
After adjusting the SWR, I heard the station II6T. 

I could easily make a QSO, using a power of just 360 milliwatt. I tried to work them, earlier in the contest, on the damaged inverted V. But they could not copy my RST on the cracking inverted V.

I am very pleased, with this first QSO on the  Red Bull  antenna. Later I realized that this QSO is a more than 1000 Miles per Watt QSO.

I made QSO's with EA, YU, SM, YL and LZ with 3.6 W

With 800 mW I managed to make a QSO with HA and a QSO with UR.

Further I made a QSO with 360 mW with an other station from Italy.
IK0YVV copied my call immediately, when I answered his CQ. His signal was strong, it was over S9.

On receive

There a large difference between wire antennas, like the half wave dipole or inverted V and the short Cylinder dipole. The signals that are received on this short antenna, are much weaker. But also the short antenna picks up less noise. I noticed that it takes some time to got used to the weaker signals. 

ARI DX contest 2015  -  Red Bull test antenna  - May 2015  -  PA1B

Improvements and Next steps

• The next step is building the same antenna with larger cans and a larger coil former, so the antenna will resonate at 14 MHz and therefor has a good efficiency.
• Test the antenna on 28 MHz. This frequency is near the actual resonance frequency.

From one moment to the other
I decided to put up this antenna this antenna in the ARI DX contest 2015, when my inverted V let my down. I constructed the  Red Bull  antenna to test the properties of symmetrical feeding, a few months before. The test showed that the cable, which is connected at the middle of the coil,
has no hand effect on the cable.  The antenna lay around in the shack.

Tuning and SWR are not critical
Was it properly tuned to the operating frequency? NO.
But I am very happy with the fact that the cylinder dipole is NOT critical in tuning and that the SWR is easily to adjust.

Red Bull antenna - May 2015  PA1B

Connecting the twin-lead.

One turn apart 

Cylinder dipole

I thank Franck F4HFQ for the link from Radioamateur.org to this Blog entry.  Franck writes:

Bert, PA1B, a fabriqué un dipôle cylindrique en remplacement de son antenne défectueuse pour achever un contact QRPp rendu difficile par cette dernière. Résultat ? 1000miles par Watt au premier QSO.

 Red Bull  gives you wings 
This a a catchy one liner, I could NOT resist, LOL.
Please notice that the Cylinder dipole is NOT a joke, but a very short, but working antenna.

Test antenna
A few months ago I built an experimental cylinder dipole with two  Red Bull  cans and a coil, that works as an impedance transformer, to test the properties of symmetrical feeding.
By using symmetrical feeding, the cable doesn't radiate and the cable has no hand effect.

Damaged inverted V
The ribbon of my inverted V is damaged by the wind.  I wanted to make a few nice QSO's in the ARI DX contest, but I was very disappointed by the inverted V. The SWR is constantly changing, even with the slightest bit of wind. The inverted V cracks when the ribbon moves, both on receive and transmit.

I tried to make a QSO with II6T with 360 mW on the damaged inverted. The operator repeated my call immediately correct, but because of the cracking twin lead, my exchange 001 was not received in Italy. Even when I increased my power to 3.6 W, the cracking twin lead spoiled the fun.

Indoor Cylinder dipole

Then I decided to try to use the  Red Bull  antenna. I clamped it between my book shelf.

I connected a 300 ohm twin lead between the coil of the antenna and the symmetrical tuner.
I matched the antenna with the symmetrical tuner for the lowest SWR.
The resonance frequency of the cans and the coil lays between 21 to 28 MHz, but the  Red Bull  antenna could be matched easily to 14 MHz, using a symmetrical tuner.

Into the ARI CW contest

After a while I heard II6T again, but now on the cylinder dipole, I answered their CQ with 360 mW. I got an immediate response and the QSO was easily made. WOW.
In total I made about 10 QSO's on the  Red Bull  antenne, with a power of 360 mW to 3,6 watts in the rest of the ARI DX contest.

Please read the interesting details on this amazing 12 inch long  Red Bull  test antenna,
that I used in the ARI DX contest 2015  (Click)

1000 Miles per Watt

Later I realized, that the first QSO with the cylinder dipole is good for 1000 Miles per Watt. hi.

Capacity

Cylinder dipole 4 m above ground @PA1B's shack

The magic of the Cylinder Dipole lays in the large capacity of the the two cylinders.
The coil and the capacity of the cans determine the resonance frequency of the antenna.

Auto transformer

The coil acts as impedance transformer. The 300 ohm ribbon is connected to 2 points on the coil that are 1 turn apart. The coil it self has 14 turns. 

Symmetrical feeder

The twin lead is connected to two connectors one turn apart, at the middle of the coil, to feed the dipole symmetrically. 

I chose for the symmetrical construction to avoid  hand effect of the ribbon. 

Connections, one turn apart

The Cylinder dipole

6 m WSPR analysis for Roger G3XBM

In his informative Blog, Roger G3XBM wrote about aircraft scattering of signals on 6 m.
I had the pleasure of making an analysis of the WSPR spots reported by Roger.

Drift
In WSPR the drift is measured over a period of 1 minute, so the drift is given in Hz per minute.
Recently I included Drift in my Excel spread sheet that I use to make an analysis.

Analysis

• The value in the table, such as  -4, is a spot with a drift of -4 Hz per minute.
  Positive drift means that the radio path is getting shorter and negative is longer.
• The signals of M0MVB show spots with a drift of -2 and   3 Hz per minute.
  It is possible, that there is a flight paths involved in the spots with -2 and an other path with the spots of   3 Hz per minute.
• The scattered signals with drift, sent by M0YOU are very strong, with a lowest possible power of 1 mW. The spot with no drift (0 Hz per minute) has a lowest possible power of 50 mW, thus is 17 dB weaker.
• The signals of M0EMM show no drift. So it's possible that there is no airplane scatter here, but an other form of propagation, such as difraction. Notice that all these spots are made within one hour.

Thanks to Roger. FB.

A few day ago I wrote to Roger: See article
Hello Roger, 
This evening I took some time to make an analysis of a number of spots on 6 meter.
I took the most interesting spots for airplane scatter.
I hope you like it and can place it in your blog. 
I left in M0EMM to show the difference. hi
Positive drift means the path is becoming shorter. 

The spots of M0MVB shows spots where the path is becoming shorter (+3Hz per minute)
and spots where the path is becoming longer.   (-2 Hz per minute)
I just saw that the spots of M0YOU with scatter, are much stronger than the spot without scatter. 
The lower the lowest possible power, the stronger the signal.  
A lowest possible power of 1 mW is 17 dB stronger than 50 mW. hi.
I left in the spots of M0EMM, to show that there is no Doppler and the signals are not that strong.

Good luck in further analysis,
73, Bert PA1B

Opening van het zwembad Lobeke in Lopik

Gisteren werd het zwembad Lobeke in Lopik spectaculair geopend.
De opening geschiedde met medewerking van wethouder Johan van Everdingen.

Wethouder Johan van Everdingen

 Na het praatje van wethouder Johan, werd de taart voor de grootste groep van de aanwezige scholen uitgereikt.

Wethouder Johan, Wendy, badmeester Ben en Kees (mic)

De Zomergaard kreeg de taart voor aanwezigheid met de grootste groep.
Na het uitreiken van de taart aan moeder Wendy, was het tijd om de badeenden te beoordelen.

Er werden 25 prijzen voor de leukste of mooiste badeendjes uitgereikt.
Dit naar beoordeling van wethouder Johan.

De wethouder ging gekleed in eendenpak als eerste van de duikplank te water, gevolgd door de kinderen. Bekijk het artikel op de gemeente site. Click.

Opa en Zoe in het water

We hebben genoten.
Het evenement was goed georganiseerd en de presentatie was erg leuk.

Lowest possible power

In WSPR analyses I use the lowest possible power to compare the signal strength of WSPR spots.
The lowest possible power is calculated from the transmitted power and the SNR of the receiving station. The lowest possible power is an excellent propagation indicator.

Click on the Tab: WSPR propagation analysis at the top of the Blog for a new explanation on the lowest possible power and a easy to use beatiful table.

Lowest possible power  -  Click to enlarge PA1B

I am proud at the beautiful table. hi.